|
GM 97168 LATEST Model Genius 120 Brushless Speed Controller
(Firmware Version: 12.4 installed as standard)
Note: USB programming lead is not included
Note: Installed programs for Stock motors: (No need for a computer)
Program 6: Mild timing advance for normal use
7: Medium timing advance for motors with inbuilt high advance
8: High timing advance for expert or motors with a low or reduced timing
9: Max timing advance for expert.
IMPORTANT: When plugging in the sensor connector, hold with the wires and gently push in straight down. DO NOT force plug in at an angle or push down hard on the plug as you may bend the small pins
Note: To use the online downloads, you must install the USB driver , (See USB driver link furthur down.)
NOTES:
To read the max motor revs and amp draw at the end of a run, or when bench testing:
After the run or after revving up.
Press the button on the speed control once. Then unplug from battery.
Plug in the USB connector and read to computer
The revs and amps will be shown at the top of the Telemetry page
NOTE: When testing on the bench: The motor may pulse at full revs. This is to stop the motor over reving and blowing the rotor or a winding. It will not pulse on the track or under load.
To set the switching point:
Disconnect the sensor cable from the speed control
Rev the motor in the car (with the wheels spinning) to full speed.
Return to neutral and press the button on the speed control
Attach the USB cable and read the data which will show the revs of the motor
Set the switching point to half of that value for indoor tracks.
For outdoor tracks with longer straights set the switching point between half and 2/3rds of that value.
(How to reset: Plug into Lipo and turn on. Hold down button until it beeps. Release and then hold down button again untill it beeps (3 times). Release button. Wait until it beeps 3 times again.. Turn off and then it is ready to set to transmitter.
To set to transmitter: Plug in and turn on. Hold down button until it beeps. Release button
Pull transmitter stick(trigger) to full throttle (program1) then push to full brake(program2), pull to full throttle(program3)
Continue until you reach the number you want. Then hold the transmitter stick(trigger) in that position until the speed control beeps.
Release stick and then speed control will be in the new program number you have selected.
Note: You must set the transmitter throttle to 100% forward and 100% brake before programing, for this to work correctly.
Model includes free firmware updates online and external Capacitors. Many other features below
Note: USB is not included.
NOTE: When testing on the bench: The motor may pulse at full revs. This is to stop the motor over reving and blowing the rotor or a winding. It will not pulse on the track or under load.
Characteristics:
Lower operating temperatures thanks to a case aluminium and a specific Design PCB with legs coppers extremely thick and a face of commutation optimized. the centre of gravity is very low thanks to a design flat.
Degree of higher output thanks to a new processor 16Bit even faster, an optimized software and a hardware even simpler to use. One obtains thus more power, and times of use even longer.
For Brushless engines (see tension of use) and for engines with coals (until 7,4V)
Telemetric functions
Automatic recognition of sensors Hall
Recording/restitution number of revolutions max, the intensity max, temperature
New programs for braking and the power
10 programming methods user
Possibility of update user
Base of welding for a simple replacement of the cords
Programmable functions:
Function Goes/stop on key
Regulation of undervoltage: automatic for accumulators Li-/Ni or by adjustable stage of 0,1V
Automatic brake, mini brake, maximum brake, total braking, function braking ABS
Maximum reverse gear, various modes of reverse gear
Automatic gas
Progressive starting, gradual braking
Limitation of the intensity, limitation of the intensity to starting, Turbo
Positions of the handle of ordering of the transmitter: full throttle, neutral, braking totel, neutral
Timing, of the functions Timing variables
Curve of power 16 points for 3T - 21,5 T
Cut in the event of too high temperatures, sensors modes, braking modes, type of Motor
Frequency 0,25 - 32 Khz
Other functions using PC software!
Design features
Protection of surge protection
Weight with wiring: 99 G
Programable
Weight without wiring: 64 G
A number of elements, Pb: 3 - 6
R DS one der FETs EIB 25°C: 0,0004 Ohm W
NOZZLE: 5,8/kurzz. 4 V/A
Frequency: 0,25/0,5/1/2/4/8/16/32 Khz
NOZZLE max. dissipated power: 2,5 W
Fall of tension under 20 a: 0,008 V
Closed-circuit current under 25 C: (Bürstenlose Motoren) 120 A
A number of elements, LiPo, Lilo: 2 - 3
Impulsstrom EIB 25°C: 800 A
A number of elements, NiCd, NiMH: 4 - 10
Dimensions: 44 X 31 X 27 mm
Supply voltage: 4,8 ... 12 V
|
